| ## Refer to http://caffe.berkeleyvision.org/installation.html | |
| # Contributions simplifying and improving our build system are welcome! | |
| # CPU-only switch (comment to build without GPU support). | |
| USE_CUDA := 1 | |
| # uncomment to disable IO dependencies and corresponding data layers | |
| # USE_OPENCV := 0 | |
| # USE_LEVELDB := 0 | |
| # USE_LMDB := 0 | |
| # uncomment to allow MDB_NOLOCK when reading LMDB files (only if necessary) | |
| # You should not set this flag if you will be reading LMDBs with any | |
| # possibility of simultaneous read and write | |
| # ALLOW_LMDB_NOLOCK := 1 | |
| # Uncomment if you're using OpenCV 3 | |
| OPENCV_VERSION := 3 | |
| # To customize your choice of compiler, uncomment and set the following. | |
| # N.B. the default for Linux is g++ and the default for OSX is clang++ | |
| # CUSTOM_CXX := g++ | |
| # CUDA directory contains bin/ and lib/ directories that we need. | |
| CUDA_DIR := /usr/local/cuda | |
| # On Ubuntu 14.04, if cuda tools are installed via | |
| # "sudo apt-get install nvidia-cuda-toolkit" then use this instead: | |
| # CUDA_DIR := /usr | |
| # CUDA architecture setting: going with all of them. | |
| # For CUDA < 6.0, comment the *_50 through *_61 lines for compatibility. | |
| # For CUDA < 8.0, comment the *_60 and *_61 lines for compatibility. | |
| CUDA_ARCH := -gencode arch=compute_30,code=sm_30 \ | |
| -gencode arch=compute_35,code=sm_35 \ | |
| -gencode arch=compute_50,code=sm_50 \ | |
| -gencode arch=compute_52,code=sm_52 \ | |
| -gencode arch=compute_60,code=sm_60 \ | |
| -gencode arch=compute_61,code=sm_61 \ | |
| -gencode arch=compute_61,code=compute_61 | |
| # Deprecated | |
| # CUDA_ARCH := -gencode arch=compute_20,code=sm_20 \ | |
| # -gencode arch=compute_20,code=sm_21 \ | |
| # -gencode arch=compute_30,code=sm_30 \ | |
| # -gencode arch=compute_35,code=sm_35 \ | |
| # -gencode arch=compute_50,code=sm_50 \ | |
| # -gencode arch=compute_52,code=sm_52 \ | |
| # -gencode arch=compute_60,code=sm_60 \ | |
| # -gencode arch=compute_61,code=sm_61 \ | |
| # -gencode arch=compute_61,code=compute_61 | |
| # Uncomment to enable op::Profiler | |
| # PROFILER_ENABLED := 1 | |
| # DEEP_NET choice: | |
| # caffe for Caffe (default and only option so far) | |
| DEEP_NET := caffe | |
| # Caffe directory | |
| CAFFE_DIR := 3rdparty/caffe/distribute | |
| # Faster GUI display | |
| # WITH_OPENCV_WITH_OPENGL := 1 | |
| # OpenPose 3-D Reconstruction | |
| # WITH_3D_RENDERER := 1 | |
| # WITH_CERES := 1 | |
| # WITH_FLIR_CAMERA := 1 | |
| # Eigen directory (Ceres) | |
| # WITH_EIGEN := 1 | |
| EIGEN_DIR := /usr/include/eigen3/ | |
| # Spinnaker directory | |
| SPINNAKER_DIR := /usr/include/spinnaker | |
| # Whatever else you find you need goes here. | |
| INCLUDE_DIRS := /usr/local/include /usr/include/hdf5/serial | |
| LIBRARY_DIRS := /usr/local/lib /usr/lib /usr/lib/aarch64-linux-gnu /usr/lib/aarch64-linux-gnu/hdf5/serial | |
| # If Homebrew is installed at a non standard location (for example your home directory) and you use it for general dependencies | |
| # INCLUDE_DIRS += $(shell brew --prefix)/include | |
| # LIBRARY_DIRS += $(shell brew --prefix)/lib | |
| # Uncomment to use `pkg-config` to specify OpenCV library paths. | |
| # (Usually not necessary -- OpenCV libraries are normally installed in one of the above $LIBRARY_DIRS.) | |
| # USE_PKG_CONFIG := 1 | |
| BUILD_DIR := build | |
| DISTRIBUTE_DIR := distribute | |
| # Uncomment for debugging. Does not work on OSX due to https://github.com/BVLC/caffe/issues/171 | |
| # DEBUG := 1 | |
| # The ID of the GPU that 'make runtest' will use to run unit tests. | |
| TEST_GPUID := 0 | |
| # enable pretty build (comment to see full commands) | |
| Q ?= @ | |